How To Make An Easy Cushion Cover

Sewing Bee Fabrics Tutorial

How To Make An Easy Cushion Cover

 

Having been asked to make an unusual cushion cover for a birthday present, this was the really easy-to-make cover I came up with. This project is perfect for beginners and experienced levels alike.

What you will need:
Half a meter of cotton for the outer pattern ( I used Michael Miller for the hedgehogs. Check out our range of Michael Miller fabrics HERE)
2 squares of 27cm x 27cm of the centre pattern in cotton

How to make it:
A cushion is typically about 45cm x 45cm,  so allowing for 1/2 inch seams I cut 5 pieces 27cm width x 22cm height and 2 pieces 47cm height x 42cm width from my half meter piece.

I joined both the 27cm x 27cm squares with a smaller rectangle piece placed above and below, by placing them right side together and sewing 1/2 inch from the edge. I pressed seams open as I went to give a neater finish.

On one side you will need to make an opening to get a cushion in, so pick a back and a front. On the top sewn rectangle on the back, I folded the top edge, then folded again so the raw edge was underneath itself and sewed the hem so that all raw edges were completely enclosed. I did a matching hem on the bottom of the 5th smaller piece (the last small rectangle piece that isn't attached to anything yet).

Next I faced the 2 main sections right side together and pinned the long vertical sections to each side. This is easier to do by folding the main panels in half so the new pieces are central. Lay the 5th spare piece over the top of the other hemmed rectangle and pin down the edges with the rest of the seam.

This should create a letterbox effect with the 2 hemmed edges. This will be where you poke your cushion through.

Sew the vertical seams then fold the vertical panels in half so the smaller cotton pattern sits centrally. Press in place.

Pin and sew the top and bottom then turn right side out through the letterbox opening.

Now all you have to do now is stuff a cushion in!

We hope you enjoy our tutorials and love hearing what you think so please leave us a comment or send me an email to linda@sewingbeefabrics.co.uk
Happy Sewing!

More sewing tutorials available at www.sewingbeefabrics.co.uk

How to make a simple cotton top hat

Sewing Bee Tutorials

How to make a cotton top hat

My little boy needed a sun hat now the weather is warming up, but the ones in the shop all looked so boring. So I thought what could look cuter than a baby in a top hat?!

What you’ll need:
I used about 30cm x 135cm patterned cotton from HERE
Interfacing (sew on or iron on is fine) I used a 43cm x 12cm strip and 2 x 25cm square pieces


How I made it:
First off I needed to know what size head to make the hat for, so I made a rough estimate and cut a hole out of some paper. I tried this on and snipped a bit. Then I had to fold the paper under to add a bit where I had got a bit scissor happy! You can make a perfect circle, but I thought it may get a better fit by making it to his exact head shape, which seems to have worked as it's never moved around on his head and he has worn it for a week without pulling it off!

I then drew around the inside of my head guide paper onto another piece of paper. I added 2 inches all around for the hat brim, and a 1/4inch (or whatever you prefer to use) as seam allowance. You will need 2 of these cut in cloth, and 2 cut in interfacing. If you make it without the interfacing it will just be floppy and wont hold it's shape.

I lay some string around the inner circle to measure the circumference to determine the length of the hat body I would need. Then I added ½ inch to allow for a seam allowance at each end – this made things a little tight to fit when I was making fine adjustments later as I needed to enlarge the head hole a little more, so if I was doing this for a wiggly child again I would do this measurement on the fabric brim after doing the fitting, as if you need to make the opening bigger, you will need more fabric. If your child (or adult) sat still and was as good as gold then you should be ok! I made my top hat 12cm tall then added ¼ seam. This will need folding over, so double this last measurement So....that was a rectangle of 43cm (plus 2 seam allowances) x 24cm (plus 2 seam allowances). Cut 1 in cloth and 1 in interfacing (or cut 2 in interfacing if you want it to be more rigid and formal).

For the top of the hat, trace the head measurement or use the centre of the brim pattern and add a ¼ inch seam allowance all the way around the outside. (If you want to make this hat even stiffer or warmer, you could always cut 2 in cloth and 1 in interfacing and just over cast stitch them together to treat them as 1 cloth). I just wanted it as a sun hat so I used a single piece of cotton to allow for heat to escape easily.

First, make your brim. You need interfacing on the outer 2 layers and the 2 cotton layers in the centre with the right sides facing together in the middle. Sew your ¼ inch seam all round the outer edge. For curved edges, I find it easier to use a ¼ inch sewing machine foot to line the fabric up with to help get an even line. (All our sewing machine feet are on sale HERE) You could also pop a piece of coloured sticky tape as a marker on your machine to line the edge up with. If you were to just turn it right side out as it is, the seam will bunch inside and look messy, so when I turn a big curve, especially one that is thick or stiffened, I cut little nicks all the way around my seam being careful not to cut the stitching before turning right sied out. I then top stitched around the edge to make it look even flatter.







Before finishing the inner circle, I double checked it on his head to make sure it sat at the level I wanted, and trimmed any misbehaving layers to give a neat inner edge. Using an overcast foot with an over-edge stitch on my sewing machine I stitched all round the inner edge.

Next I made up the hat body. I took the large panel of fabric, and placing it the right way around, folded it in half across the long side and sandwiched the interfacing in the centre. I then used the same overcast stitch to work my way around the raw edges.

I took my cotton top for the hat, and with right sides together, slowly stitched it to the hat body. I did not pin this first as I find it easier to gradually feed the circle through, matching the edges as I go. Every few stitches I left the needle down to hold the fabric and keep my stitch place, and lifted the presser foot up to pivot the fabric slightly so I could keep stitching the perfect circle without bunching my cotton.

I checked the alignment of the hat body with the brim and pinned the seam allowance at the base to get a perfect fit when sewing up the side seam. This was then stitched inside out.
Finally, I pinned, then hand stitched the brim to the body of the hat by pinching the edges together slightly and sewing an overcast stitch. I did this by hand to get a neater and more concealed finish.







All that’s left now is to wear it to all your favourite hang outs!

Don't forget here at Sewing Bee Fabrics we love hearing your thoughts and seeing your makes so leave us a comment or send us an email to linda@sewingbeefabrics.co.uk